
Nov . 13, 2026 00:49 Back to list
Summary
Hydraulic hose price makes sense only after the fluid, reinforcement, routing, connection arrangement, and required length are matched. Our SAE 100 R1 / EN853 1SN S hose has three layers and one steel wire braid for hydraulic systems using the listed fluids. Use the checks below to prepare a comparable request for the right hose configuration.
Fluid compatibility comes before a hydraulic hose price comparison. Our Steel Wire Reinforced Hydraulic Hose SAE 100 R1 / EN853 1SN S carries hydraulic fluid, petroleum-based hydraulic fluid, hydraulic oil, mineral oil, gasoline, fuel oil, lubricating oil, emulsion, glycol solution, gas, and water.
These media cover hydraulic circuits in industrial machinery, construction equipment, agricultural equipment, mining hydraulic supports, oil field development, lifting, and transportation. Name the actual fluid in your request so we can match the hose to the circuit instead of comparing unrelated hose configurations.
This hose uses a three-layer construction: an inner tube, a reinforcement layer, and an outer layer. The reinforcement is one steel wire braid, which is the defining construction of the SAE 100 R1 / EN853 1SN S designation.
Choose this configuration when the system calls for a single braided steel wire hose and flexible routing. The product suits compact machinery layouts where the hose must bend without collapsing or compromising flow. A similar-looking hose with another reinforcement arrangement is a different selection, even when the connection appears similar.
What to weigh
Required length affects the quotation and the fit of the replacement. We support specific hose lengths, so measure the existing route and identify the length needed for each assembly or replacement section. The hose should follow its intended path without sharp bends or unnecessary tension.
Connection details belong in the same request. The SAE 100 R1 / EN853 1SN designation helps technicians match fittings, connectors, and couplings. Include the connection arrangement with the hose designation so we can price the intended assembly rather than the tube alone.
The outer layer is abrasion-resistant and weatherproof. The hose is therefore suited to equipment that works outdoors or may contact surrounding surfaces during operation. The product is relevant to forklifts, loaders, agricultural sprayers, hoisting equipment, and hydraulic presses, along with mining, oil field development, engineering construction, lifting, and transportation work.
Keep the hose designation and connection arrangement consistent when comparing hydraulic hose price. A like-for-like comparison should also use the required length and marking requirement for each assembly.
A practical request names the Steel Wire Reinforced Hydraulic Hose SAE 100 R1 / EN853 1SN S and identifies the circuit medium and equipment. Add the required length, connection details, and marking requirements when the hose needs identification for maintenance, inventory control, or installation work.
We support customized hose lengths and markings. Keeping the product designation in the request ties the quotation to the single-steel-wire-braid construction and reduces confusion when several hose types are being purchased.
Your shortlist
The inner tube is oil-resistant synthetic rubber, the reinforcement is a high-tensile steel wire braid, and the outer covering is abrasion-resistant and weatherproof rubber. This combination suits hydraulic and petroleum-based fluid service while addressing contact with surrounding surfaces and outdoor exposure. The single braid remains the defining reinforcement for this product.
Yes. Glycol solution and water are included in the product’s listed media. Identify the exact medium in the circuit when requesting a hydraulic hose price so the selected hose is tied to the intended service. This check is especially useful when a system uses a water-based hydraulic fluid instead of a petroleum-based medium.
It helps technicians match fittings, connectors, and couplings for the hose assembly. The designation also identifies the single steel wire braid construction used by this product. Include the required connection arrangement with the designation when replacing a hose, because the hose type and the end connections must be considered together.
Our Steel Wire Reinforced Hydraulic Hose SAE 100 R1 / EN853 1SN S fits systems using a listed fluid that call for one steel wire braid and flexible routing in the stated equipment settings. Include the details of the intended assembly in your request so we can review the configuration and return a useful hydraulic hose price.
The company
Guangrao Juyuan Rubber And Plastic Co., Ltd. as a high-quality rubber and plastic production company. Our journey began back in 2014 with a commitment to manufacture the best rubber and plastic rubber hoses. In the meanwhile, we also provide excellent solutions and services for customers. We customized various types of special-shaped rubber hose with various models, self-produced and self-marketing with large quantity of the products and quality guarantee.…
About Us ↗Visit company website ↗This is the first article
Latest News
Steel Wire Reinforced Hydraulic Hose SAE 100 R1 / EN853 1SN S
NewsOct.17,2024
Two Layers Steel Wire Reinforced Hydraulic Hose SAE 100 R2 / EN853 2SN
NewsSep.03,2024
Textile Braid Reinforced Hydraulic Hose SAE100 R3+R6
NewsSep.03,2024
Textile Reinforced Hydraulic oil Suction Hose with embedded Steel Wire SAE 100 R4
NewsSep.03,2024
Single Wire Braid and Textile Covered Hydraulic Hose SAE 100 R5
NewsSep.03,2024
High Pressure Thermoplastic Hydraulic Hose SAE 100 R7 / EN855 R7 - SAE 100 R8 / EN855 R8
NewsSep.03,2024
Heavy Duty Four-layer Steel Wire Spiral Reinforced Hydraulic Hose SAE100R9+R10+R12
NewsSep.03,2024
Heavy Duty Multi-layer Steel Wire Reinforced Hydraulic Hose SAE100R13 SAE100R15
NewsSep.03,2024
Latest Products